74121 MONOSTABLE MULTIVIBRATOR PDF

Description and operation of a 74L and Monostable Multivibrator. The shown above provides a single Monostable Multivibrator function. SNN from TEXAS INSTRUMENTS >> Specification: Monostable Multivibrator, , 45 ns, 16 mA, V to V, DIP MONOSTABLE MULTIVIBRATOR WITH SCHMITT TRIGGER INPUT This multivibrator features dual negative-transition-triggered inputs and a single.

Author: Kijin JoJokinos
Country: Oman
Language: English (Spanish)
Genre: Music
Published (Last): 17 December 2015
Pages: 491
PDF File Size: 7.17 Mb
ePub File Size: 6.62 Mb
ISBN: 455-9-71302-860-8
Downloads: 36071
Price: Free* [*Free Regsitration Required]
Uploader: Mezile

The circuit could be used for any TTL family, such as LS, or H, but the load capacitor might need to be changed to reflect that.

Frequency meter with monostable multivibrator

By the way, the ammeter PA1 can be replaced with a digital multimeter. How to Read Logic Truth Tables: C5 and trimming potentiometers R The two graphs below show the resultant pulse width for different values multivibratkr resistors and capacitors. All this allows to create very simple frequency meter circuit with several frequency ranges: VD4 protects the integrated circuit from overloading.

The first chart works for either the 74L multivivrator 74L; however, the second monostablw only applies to the 74L The Figure 1 shows the circuit diagram of the frequency meter, the circuit based on the digital IC The pin out diagram works any any style 74xx or 74xx DIP chip, but the timing graphs are only valid for the TTL families indicated.

  IMAGE GRAMMAR NODEN PDF

The shown above provides a single Monostable Multivibrator function. The Diodes used in the circuit are 1N or equivalent. This device uses the ammeter with full-scale deflection of multivlbrator. Also refer to Transistor Multivibrator Circuits.

The pulse voltage is proportional to the input frequency, through the diode VD5 this voltage charges the capacitor C1. To use the internal timing resistor connect Rint to Vcc.

Note the uses a 4k internal resistor, while the uses a 20k resistor. A quartz crystal oscillator circuit that can generates kHz signal with a 3-stage decade counter can be used as a reference frequency source see the Figure 2.

You’ll need a source of stable frequency reference signal that can produces a set of frequencies Hz, 1 kHz, 10 kHz and kHz. A Monostable Multivibrator is also called a One Shot.

The first method for a Cx of less than pF [below] and a second connection [below that] for an external capacitor, Cx, of greater than pF. While the shown below provides a mnoostable Monostable Multivibrator function with clear. This IC is the monostable multivibrator that may generate a pulse of a different width from 35 ns and wider that depends on RC components. Digital integrated circuits can be used in the design of an analogue frequency meter with a frequency range to several MHz.

Adjust the trimming potentiometer R3 to move the needle of ammeter PA1 to the maximum value on the scale.

  ANIP ANGOLA PDF

Frequency meter with monostable multivibrator Digital integrated circuits can be used in the design of an analogue frequency meter with a frequency range to several MHz. The pulse frequency multivibratro on the input frequency. How to calibrate this frequency meter? There are multviibrator different methods of connecting Rx and Cx. The ammeter PA1 indicates the voltage across the capacitor C1. 7412 pulse width produced by the monostable multivibrator depends on the values of capacitors C The load Capacitance CL is 50pF, including scope probe, wiring, and any stray capacitance.

Do the same operation for all ranges.

Frequency meter with 74121 monostable multivibrator

The device can measure sinusoidal wave and square wave input signals. The number of frequency monlstable can be increased by using a rotary switch SA1 with more than four positions, and by adding some additional RC components.

Turn the rotary switch S1 of the frequency meter to the range of Hz and connect the device to the reference signal source of Hz. All this allows to create very simple frequency meter circuit with several frequency ranges:. Instead ofthe SN or DM can be used. Reference oscillator circuit diagram.