ARCMATE 100I PDF

CNC Manual/Fanuc Robotics/Fanuc Robot ARC Mate i MODEL B Maintenance Manual M-6i. Fanuc Robot ARC Mate i MODEL B Maintenance Manual. Refurbished Fanuc M-6i / Arcmate i with RJ2 control and pendant. Recommended applications: Material Handling, Press tending, CNC machine tending. Fanuc Arcmate i robots with RJ3 Control, Welding robots Comes Tested Available in Large Quantities All Of Our Robots Are Tested and in A Condition.

Author: Taktilar Jugul
Country: Cuba
Language: English (Spanish)
Genre: Love
Published (Last): 11 December 2005
Pages: 259
PDF File Size: 6.10 Mb
ePub File Size: 4.12 Mb
ISBN: 822-2-22151-330-6
Downloads: 71564
Price: Free* [*Free Regsitration Required]
Uploader: Tuhn

It comes with Kfloppy. If you make any headway, please share the details. The left left corner tells when the question was posted. Thanks again for the help from forum members!

The extrusions are on a rotating fixture so that all the welds can be done. I’m rather surprised your it guy didn’t know this.

It cannot be reconfigured to listen to the serial arcmmate.

July 31, Started by zaneta30 on Fanuc Robot Forum. July 01, If I used fixed stations I arcmahe up clamping and unclamping the part six or eight times depending on access. Perhaps someone will chime in. I was of the understanding that the STE Bridge software would create this connection, which could then be picked up on the network – or better yet, on the server laptop itself. I hope that I can give back something to the robot community Each time I sent a packet, the laptop “server” would show 16 bytes 1100i, and the desktop “client” would show 16 bytes received.

Do you have access to the Fanuc CRC? The serial port is a serial port, your network interface is a network interface. Once the program starts it moves to a point on the fixture center punch mark which is in a different point for every orientation of the fixture, I just check that it lines up and start the next cycle.

  COURS OFPPT TSGE PDF

So I tried a couple pieces of software – Serial-to-Ethernet “Bridge” software. I now find the difference between this position register and the originally programmed position and store this in a third position register.

Fanuc M6i / Arcmate i RJ2 in Greenville, PA, USA

I found my old desktop with WinXP on it, and a serial port on the back. I have tried the following: I do NOT have K-floppy software. In theory you can run any protocol over a serial port, but both sides need to do this, you 100u unilaterally decide to treat your serial port as a network device. I am also still seeking the Kfloppy software so I might try to just use the older, simple method of backing arccmate up.

ERBU free demo version is all I need to make simple backups. I do not yet have access to the CRC. RJ controller – has RSC 25pin on front.

Any insight on Fanuc programming is welcome. November 05, I guess if I understand correctly, Kfloppy is listening for serial protocol and will avoid the need for any other software or hardware other then the fabricated cable.

I have a laptop with RS 9pin on the back. I will do the same. December 31, I move the tip to the corner of the work piece using the pendant and save that point as a second position register.

It’s not just a matter of getting the 100l to a network point of communication. I’m trying to setup a connection via the serial rs port with a pc and it just dont seem to work.

  LA ULTIMA LECCION RANDY PAUSCH PDF

To my knowledge, the Fanuc controller does not support this, so regardless of what you 100u on your laptop you cannot use the program you mentioned and expect it to work. I have now copied and pasted the program so that it runs 4 times in one program, there is a pause programmed in for me to turn the fixture and mount the next part.

The upper right tells 100u join date. Here is where I am struggling, I can use the program shift utility to move the relevant sections of the program manually but I would like to do it from within the program.

Fanuc ARCMATE I R-J2 communication in Fanuc Robot Forum – Page 1 of 1

And welcome to the forum! I am registered with Fanuc but waiting to hear back from them. My success was as far as actually seeing packets of info 010i transferred when I would try to backup TP programs from the teach pendant. Started by latendal on Fanuc Robot Forum. This will not work.

Fanuc Arcmate

Program starts and moves to a point position register near the corner of the work piece. I would like to put some steps in the beginning of the program to check and adjust the programmed positions.

I made up what I believe is the right custom cable.