ASTM D1457 PDF

Find the most up-to-date version of ASTM D at Engineering ASTM D Lb9 LT5 m. D compaction are terms used interchangeably with preforming for PTFE. reground resin. Buy ASTM D Standard Specification for PTFE Molding and Molding and Extrusion Materials from SAI Global.

Author: Aragrel Faera
Country: Maldives
Language: English (Spanish)
Genre: History
Published (Last): 21 February 2006
Pages: 52
PDF File Size: 3.26 Mb
ePub File Size: 20.67 Mb
ISBN: 924-7-85573-387-4
Downloads: 52744
Price: Free* [*Free Regsitration Required]
Uploader: Malalkree

We d157 therefore recommend that any customer looking to write a general lined piping specification bases it upon the ASME standards.

The term grade B determines the chemical composition and mechanical performance of the steel used to make the pipe. There are some differences between this modern specification and the older series, these are mostly in the text and astm d of little significance in terms of performance. The larger sole plate or slide bearing component should be installed in the upper position and fully cover the smaller slide bearing component in every direction of movement. Visit us at www.

Lubron TR PTFE bearing components may be procured separately, although we strongly recommend purchasing s1457 the upper and lower components to assure optimum performance and reliability.

They are called granular because of the large form of astm d polymer agglomerates produced during the raw polymer ast processes. Static Coefficient of friction.

Schedule This is a term for the internationally recognised range of nominal wall thicknesses for carbon steel and stainless steel pipes. ISO deals with the requirements that organizations wishing to meet the standard have to fulfil.

This raw material specification is still in common use and d14457 frequently referred to although it was superseded by Asfm type specifications astm d Astm d follows the basic format of F These types of PTFE are almost always mixed with a volatile processing aid and v1457 used to make high quality extrusions. Bearings which do not fully satisfy all the testing and inspection requirements shall be replaced or repaired to the satisfaction of astmm Project Engineer.

It was written basically for two reasons, firstly to provide a specification for the many types of lined system within a common document and secondly to regularise the various differing techniques used by astm d major US manufacturers. For cast-in-place concrete applications, LUBRON TR slide bearings can be supplied with anchor studs welded to the sliding surfaces must be maintained clean and free of dirt, grit and other contaminates which could effect the performance or service life of the bearing assembly.

  DAIDO MORIYAMA THE WORLD THROUGH MY EYES PDF

Any remaining traces of contamination shall show only as slight astm d in astm d form of spots or stripes. It is generally a compilation of the original liner specific standards and includes all the common lining materials plus several more unusual types. Slide bearings shall be designed to accommodate the total movement as specified.

ISO deals with the requirements that organizations wishing to meet the standard have to fulfil. Testing shall be performed in-house or by an independent testing laboratory subject to the approval of the Project Engineer. Wear resistance with Taber abraser method. We ourselves have reached a dead-end on a number of metrics, but we have done our best to fill the gaps using verifiable data. Much of this specification is taken up with test methods for d materials as delivered by the polymer manufacturer and how the sintered ast is to be tested by the end user.

This specification is widely used in the Grade B form as the standard pipe material for Lined Pipe and Fittings manufacture. The astm d covers physical and mechanical properties of the various d1547 d of these polymers both atm and after sintering.

Astm d specification also contains details astm d test methods astn be used for PFA polymers.

Unraveling Polymers: Charting the standards used in defining PTFE properties

These materials which are often called fine powders are characterised by their consistent high performance, superior permeation resistance and excellent surface finish. It does theoretically supersede all astm d single liner type specifications but in practice it operates alongside the older specifications.

The maximum bearing movement, dimensions “E” and “F”, must be added to dimensions “C” and “D” respectively. These materials astm d are astm d called fine powders are characterised by their consistent high performance, superior permeation resistance and excellent surface finish.

It has been mandatory throughout the EU since A type reference determines the mechanical and thermal astm d of Page 3 of 5 a particular grade or type. Slide bearing assemblies aztm be tested if required in full compliance with the Project Plans, Specifications and Special Provisions.

  CONVERT OTFSPOOLJOB 2 PDF

Whilst the mechanical properties are important it is the thermal properties which have the most significance when PFA is astm d as a corrosion resistant lining material. These are obviously relevant for this specification, satm the more generic data about lining materials is much less definitive than astm d ASME specifications. To accommodate maximum horizontal movement, the required upper bearing plate or stainless steel sole plate size for standard bearing plate sizes can be determined using the following table.

Fluorinated Ethylene Propylene Copolymer (Melt Flow Index MI)

The coefficient of friction generally decreases slightly with an d14557 in surface temperature. Silicon grease conforming to Military Specification MIL-S is generally recommended for most structural applications.

We offer a variety of engineering services from the selection of bearing materials to in-house testing of bearing assemblies to simulate load, movement, velocity, temperature and other environmental conditions present during the actual operation of LUBRON TR bearings. The standards are published by ISO, the International Organization for Standardization, and available through National standards bodies while meeting statutory and regulatory requirements. Maximum vertical load is assumed to be the total dead and live loads.

Corrosion protection including painting and metallic coating of all exposed carbon steel surfaces shall be performed in accordance with Project Plans, Specifications and Special Provisions.

Fluorinated Ethylene Propylene Copolymer (Melt Flow Index 10-35 MI)

Deformation D157 Load — Total deformation after 24H. This specification astm d widely used in the Grade B form as the standard pipe material for Lined Pipe and Fittings manufacture.

The specification also contains details of astm d methods to be used for PFA polymers. Type or Type with a mirror finish not exceeding 10 microinches 0. Corrosion resistance especially resistance to stress corrosion cracking at elevated temperatures is determined by the molecular weight and structure of the PFA. Using the appropriate bearing design load d1475 maximum vertical d1547, select the proper lower bearing plate size and corresponding upper plate or sole plate size.