High pressure screw plug (also called breech lock) exchangers are of the most reliable heat exchangers in the plant, it is very clear to me that. Threaded Closure Heat Exchangers. FBM-Hudson Italiana has developed design and manufacturing know-how to prevent hydrogen and high temperature . SCREW PLUG OR BREECH LOCK HEAT EXCHANGER (EASIER MAINTENANCE+SHORTER SHUTDOWN TIME = HIGHER EFFICIENCY) Presented by.
With the jig it is possible to open the channel, remove the internals, assemble and reclose of the Breech-Lock The exchangers in a ehat short time without need of heavy cranage.
Shell & Tube Heat Exchanger Manufacturers in India
After traveling around the world helping facilities turn these exchangers from chronic leakers from internal tubesheet and external diaphragm and B style shell leaks to one of the most reliable heat exchangers in the plant, exchamger is very clear to that manufacturers, engineers and mechanics struggle to correctly understand the interactions between gaskets, internal pressure, the two circles of external push bolts that are part of A style exchangers and all the internal parts.
It can be seen by analysis that the magnitude of bending stress can amount to three times the average longitudinal stress in the undercut area. breechh
Heat ExchangersHome. The pressure load is absorbed by the threaded closure and the outer row of external bolts applies the seating load to the channel gasket.
A spreadsheet that will easily analyze the critical variables; 2. You Might Also Like.
Help Center Find new research papers in: Some manufactures have given up on trying to make these connections operate leak free, and prefer to weld in the tubesheets and diaphragms. The inner row of external bolts is used to increase the seating load between the tubesheet and shell gasket in the event of relaxation of the inner bolts.
Log In Sign Up. Correct gasket selection; 3. Lower capital expenditure, easier maintenance, shorter shutdown time means higher plant reliability, lower total life-cycle cost. After the catastrophic failure that occurred in a high-pressure Screw Plug enclosure in Japan and subsequent failures that were witnessed time and again in several parts of the world, this design screw plug lost its significance to a large extent.
FEA analysis carried out at TEMA INDIA
Detailed design has been improved and optimized over the years, even on minor details that can affect reliability and maintenance. Click here to sign up. Exchsnger higher wall thickness of the channel barrel immensely shoots up the cost of the forging.
Remember me on this computer. These exchangers are easy to operate and comparatively easy to dismantle and reassemble, which results in more reliable operation and shorter shut down time. This further resulted in expelling of the oock in an extreme circumstance, causing an explosion or jamming of the threads as was often experienced.
TEMA INDIA decided to conduct an extensive research program to bring about key changes to make this screw plug heat exchanger design totally safe and free of maintenance problems. Haresh Sippy, is just like a Fisherman who has to buy Fish!
A special threaded ring hold the channel cover and contain channel pressure. Dismantling and reassembling operations.
Screw Plug (Breech Lock) Heat Exchanger by TEMA INDIA – Haresh Sippy
The internal bolts are used to apply the seating load to the gasket at the tubesheet and shell interface. Designed and manufactured with the closest tolerances and highest attention to detail for reliability, easy maintenance and enhanced safety. Correct assembly procedures that focus on important steps including proper spacing of internal parts and obtaining consistent thread friction; 4. Enter the email address you signed up with and we’ll email you a reset link. This resulted in bell mouthing in the threaded region thereby reducing breecu shear area of the threads, i.
Therefore this dilation, that is a cause of reduction in shear area, has to be restricted by using higher wall thickness in the threaded region. The tubesheet for the Breech-Lock heat exchanger is designed for a differential pressure.
And exchxnger hot torqueing the exchangers after startup. This phenomenon can be logically understood and supported by calculations to show that the combined bending and longitudinal stresses on the undercut surface of the threads produce a wedging action that results in radial displacement, causing dilation of the channel. Skip to main content. This significantly adds to the cost and time needed to open and close these breecn, as special equipment is needed to machine out the parts and weld them back together again.
Privacy & Cookies Policy
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.