Canon, the Canon logo, and imagePROGRAF are trademarks or registered Ink used for maintenance purposes such as head cleaning is absorbed. (Replace. Complete The Survey. No, Thank You. Canon · Consumer Product Support imagePROGRAF Series Support – Download drivers, software, manuals. Products. imagePROGRAF iPF Drivers & Downloads; Manuals; NEED SERVICE? imagePROGRAF iPF Specifications · Drivers & Downloads · Manuals.

Author: Malazahn Shamuro
Country: Belgium
Language: English (Spanish)
Genre: Art
Published (Last): 28 February 2017
Pages: 29
PDF File Size: 6.89 Mb
ePub File Size: 8.60 Mb
ISBN: 837-4-96509-124-9
Downloads: 86442
Price: Free* [*Free Regsitration Required]
Uploader: Fekus

Page 95 Chapter 1 2.

Installation Chapter 3 3. The tanks are also available in two capacities: Ink tank Remove all ink tanks.

imagePROGRAF iPF – Support – Download drivers, software and manuals – Canon Europe

Unpacking And Installation Chapter 3 3. Allowed tilting angle Lengthwise: Opf9000 Chapter 4 4. Handling The Printer Chapter 1 1. Page Contents Contents 7. Chapter 4 1 To remove the valve motor unit, remove the ink tank cover unit. During the relevant warranty period, Canon shall, in its sole discretion and without charge, repair or replace any defective Printhead with a new or comparable rebuilt Printhead. In the United States: Interface Specifications Chapter 1 1. Details Of Service Mode Chapter 7 7.

Chapter 6 2 Check serfice input value Input the correct value of the remaining length of the roll media when setting it. Chapter 3 11 Remove the ejection support and lower the ejection guide.

Canon iPF9000 Series. Service Manual. Parts Catalog

Chapter 4 – To remove the carriage unit, pull it out of position keeping the carriage unit level with care not to harm the linear scale. F [1] Linear Scale [2] Carriage Shaft The carriage serves a key role in printing.


Table Of Contents Contents 6. Chapter 2 c Pump The pump suction pump is a tube pump that pressurizes the ink tubes with rotating rollers to generate canoon negative pressure for sucking inks.

F Do not place or transport the printer with load placed only at the center of the printer.

imagePROGRAF iPF9000

Monday to Friday 8: The paper will be fed, if necessary, so that the sheet is at least 10 cm Page Chapter 2 e Subtank The subtank installed under each ink tank complements the work of the ink tank, agitating the ink in the tank. Printing is performed for each color using a maximum of 16 paths in each print mode according to the selected print quality. Printer Mechanical System Chapter 2 2. Weight Joint Weight Roll 7 pcs.

Canon will release technical information as the need arises. Page 89 Chapter 1 3 Store the left and right Basket Rods. Main Menu Settings Main menu items are described in the following tables. Don’t have an account? Feed roller bearing [3] F 4.

Chapter 3 8 Remove the ejection support and lower the ejection guide. Pay careful attention to all individually packaged service part carriage unit, purge unit, ink tank unit, and other parts boxes marked “This side up” and handle appropriately. Insert the protruding portion [1] of each leg cover in the groove [2] in the stand upper stay, and insert the protruding portions [3] of the leg cover in the grooves [4] in the stand lower ipf900. If the stand is assembled by only one person, injury or deformation of the stand can result.


The job preservation was executed when the permanent preservation area of the hard disk private box has already preserved one-hundred jobs. Page Chapter servixe 8 Fold back the flaps of the stand support cardboard as shown, and then remove the stand support cardboard by collapsing it. Taking up begins automatically when a sensor attached to the bottom of the stand detects a roll delivered after printing falling down due to the weight of a weight roller. Less than 1W Compliant with Executive Order.

Reinstalling the feed motor To reassemble the feed roller drive timing belt [3] into position, set the tension of timing belt [3] by adjusting the pressure of spring [4]. Page Chapter 3 4 While aligning the triangle marks at the back of the printer with the triangle marks at the back of the stand, place the printer on the stand. F F [1] When storing printed documents on the Output Stacker, set it to this position. Adjustment And Setup Items Chapter 4 4. Choose Yes to cut the roll at the sedvice position.