DIN EN ISO 2812-3 PDF
Paints and varnishes – Determination of resistance to liquids – Part 3: Method using an absorbent medium (ISO ); German version. Buy DIN EN ISO PAINTS AND VARNISHES – DETERMINATION OF RESISTANCE TO LIQUIDS – PART 3: METHOD USING AN ABSORBENT. DIN EN ISO Paints and varnishes – Determination of resistance to liquids – Part 3: Method using an absorbent medium (ISO ).
| Author: | Maurg Mular |
| Country: | Brazil |
| Language: | English (Spanish) |
| Genre: | Literature |
| Published (Last): | 16 August 2006 |
| Pages: | 270 |
| PDF File Size: | 3.4 Mb |
| ePub File Size: | 20.57 Mb |
| ISBN: | 871-3-32343-662-9 |
| Downloads: | 91688 |
| Price: | Free* [*Free Regsitration Required] |
| Uploader: | Vojind |
In the unlikely event that a problem relating to it is found, please inform the Central Secretariat is the address given below. Assessment of degree of filiform corrosion ISO Low-carbon cast-steel shot ISO Determination of tralopyril release rate by quantitation of its degradation product in the extract ISO Check standard for current issue prior to usage.
ISO 色漆和清漆 耐液体介质的测定 第1部分：在除水以外的液体中沉浸 – MBA智库文档
February Number of pages: Assessment of degree of blistering ISOPaints, varnishes and raw materials for paints and varnishes — Sampling 3 Principle A coated test panel is exposed to a test liquid by immersion in the test liquid. Use only analytical-grade chemicals. The work of preparing International Standards is normally carried out through ISO technical committees.
General test methods ISO Assessment of degree of delamination and corrosion around a scribe ISO In this Section terminological inconsistencies may occur as the fn titles are used. Preparation and protection of steel substrates ISO Determination of water-soluble chlorides ISO For dated references, only the edition cited applies.
Method using an absorbent medium Paints and varnishes – Determination of resistance to liquids – Part 4: Evaluation of delamination and corrosion around a scribe ISO Unless otherwise ddin, no part of this publication may be reproduced 28812-3 utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s member body in the country of the requester.
Plastic parts which are only primed must only fulfill the requirements specified in Table 2, no. Assessment of degree of rusting ISO Rate any visible alterations as specified in ISO Gas-chromatographic method ISO NOTE 1 28123 for technical reasons an increased total paint coat thickness is necessary, this must be agreed upon by the parties involved.
DIN EN ISO – October
Measurement of chloride on steel surfaces prepared for painting ion detection tube method ISO Raw materials ISO Cover the vessel and leave it to stand without stirring. Constant-loading method ISO Rust grades and preparation grades of uncoated steel substrates and of steel substrates after overall removal of previous coatings ISO Rotating abrasive rubber wheel method ISO Field method for the refractometric determination of moisture ISO Dry or stove and age if applicable each coated test rod for the specified time under specified conditions.
Determination of particle size distribution ISO Execution and supervision of paint work ISO Clean off any dried residue of aqueous test liquids under running water, and clean off the dried residue of any other test liquids with a solvent that does not attack the oso.
Behavior in pressure washer test acc. Page 4 TL Field method for the titrimetric determination of water-soluble ferrous ions ISO Spotting methods ISO Determination of phthalic anhydride content ISO Deviations require a corresponding drawing entry or a separate release.
May Number of pages: Pyknometer method ISO Calculation of colour differences ISO Wave-scan plus, measurement acc. Every care has been taken to ensure that the file is suitable for use by ISO member bodies.
Assessment of degree of flaking ISO Assessment of the storage stability of thermosetting powders ISO Guidance on the estimation of the probability of condensation prior to paint application ISO Assessment of degree of chalking by velvet method ISO Reference number ISO Disc or ball viscometer operated at a specified speed ISO The supplier is obligated to remove the cause for complaints occurring during this test and to improve the paint system.
This electronically generated standard is authentic and valid without signature. Field method for the conductometric determination of water-soluble salts ISO